1 files changed, 101 insertions, 0 deletions
diff --git a/authz-test/TestSuite/Instructions_for_MTCs/MTC_Appr_README.txt b/authz-test/TestSuite/Instructions_for_MTCs/MTC_Appr_README.txt
new file mode 100644
index 00000000..d7ecee45
--- /dev/null
+++ b/authz-test/TestSuite/Instructions_for_MTCs/MTC_Appr_README.txt
@@ -0,0 +1,101 @@
+#-------------------------------------------------------------------------------
+# ============LICENSE_START====================================================
+# * org.onap.aaf
+# * ===========================================================================
+# * Copyright © 2017 AT&T Intellectual Property. All rights reserved.
+# * ===========================================================================
+# * Licensed under the Apache License, Version 2.0 (the "License");
+# * you may not use this file except in compliance with the License.
+# * You may obtain a copy of the License at
+# * 
+#  *      http://www.apache.org/licenses/LICENSE-2.0
+# * 
+#  * Unless required by applicable law or agreed to in writing, software
+# * distributed under the License is distributed on an "AS IS" BASIS,
+# * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# * See the License for the specific language governing permissions and
+# * limitations under the License.
+# * ============LICENSE_END====================================================
+# *
+# * ECOMP is a trademark and service mark of AT&T Intellectual Property.
+# *
+#-------------------------------------------------------------------------------
+NOTE: You may find slight differences between this readme doc and your actual output in places such as <YOUR_ATTUID>, times, or other such fields that vary for each run.
+
+Do NOT replace anything inside square brackets such as [user.name] Some commands listed here use this notation, but they are set up to work by just copying & pasting the entire command.
+
+run command:		sh ./tc MTC_Appr1
+you should see:		MTC_Appr1
+					SUCCESS! [MTC_Appr1.2014-11-03_11-26-26]
+
+
+open a broswer and goto the gui for the machine you're on. For example, this is the home page on test machine zltv1492: 
+https://zltv1492.vci.att.com:8085/gui/home 
+
+click on My Approvals
+
+click the submit button at the bottom of the form with no approve or deny buttons selected
+
+you should see:     No Approvals have been sent. Try again
+
+click "Try again" link
+
+you should see:     The Approval Request page
+
+NOTE: a radio button is a (filled or unfilled) circle under approve or deny
+click the select all link for approve
+
+you should see:     all radio buttons under approve should be selected
+
+click the select all link for deny
+
+you should see:     all radio buttons under deny should be selected
+
+click the reset button at the bottom of the form
+
+you should see:     NO radio buttons should be selected
+
+Try to select both approve and deny for a single entry
+
+you should:         not be able to
+
+approve or deny entries as you like, then click submit
+
+after you have submitted all approvals, go back to My Approvals page
+
+you should see:     No Approvals to process at this time
+
+in your command line,
+run command:		aafcli ns list name com.test.appr.@[user.name].myProject
+
+NOTE: what you see here will depend on which entries you approved and denied. Included are 2 examples of what you can see:
+
+1) If you approve everything
+
+List Namespaces by Name[com.test.appr.<YOUR_ATTUID>.myProject]
+--------------------------------------------------------------------------------
+com.test.appr.<YOUR_ATTUID>.myProject
+    Administrators
+        <YOUR_ATTUID>@csp.att.com                                                      
+    Responsible Parties
+        <YOUR_ATTUID>@csp.att.com                                                      
+
+
+2) If you deny everything
+
+List Namespaces by Name[com.test.appr.<YOUR_ATTUID>.myProject]
+--------------------------------------------------------------------------------
+
+
+run command:		sh ./tc MTC_Appr2 dryrun
+you should see:     a lot of output. It's fine if you see errors for this command.
+
+run command:        aafcli ns list name com.test.appr
+you should see:     List Namespaces by Name[com.test.appr]
+--------------------------------------------------------------------------------
+
+
+run command:        aafcli ns list name com.test.appr.@[user.name]
+you should see:     List Namespaces by Name[com.test.appr.<YOUR_ATTUID>]
+--------------------------------------------------------------------------------
+