diff options
Diffstat (limited to 'kube2msb/src/vendor/github.com/opencontainers/runc/libcontainer/configs/network.go')
| -rw-r--r-- | kube2msb/src/vendor/github.com/opencontainers/runc/libcontainer/configs/network.go | 72 |
1 files changed, 0 insertions, 72 deletions
diff --git a/kube2msb/src/vendor/github.com/opencontainers/runc/libcontainer/configs/network.go b/kube2msb/src/vendor/github.com/opencontainers/runc/libcontainer/configs/network.go deleted file mode 100644 index ccdb228..0000000 --- a/kube2msb/src/vendor/github.com/opencontainers/runc/libcontainer/configs/network.go +++ /dev/null @@ -1,72 +0,0 @@ -package configs - -// Network defines configuration for a container's networking stack -// -// The network configuration can be omitted from a container causing the -// container to be setup with the host's networking stack -type Network struct { - // Type sets the networks type, commonly veth and loopback - Type string `json:"type"` - - // Name of the network interface - Name string `json:"name"` - - // The bridge to use. - Bridge string `json:"bridge"` - - // MacAddress contains the MAC address to set on the network interface - MacAddress string `json:"mac_address"` - - // Address contains the IPv4 and mask to set on the network interface - Address string `json:"address"` - - // Gateway sets the gateway address that is used as the default for the interface - Gateway string `json:"gateway"` - - // IPv6Address contains the IPv6 and mask to set on the network interface - IPv6Address string `json:"ipv6_address"` - - // IPv6Gateway sets the ipv6 gateway address that is used as the default for the interface - IPv6Gateway string `json:"ipv6_gateway"` - - // Mtu sets the mtu value for the interface and will be mirrored on both the host and - // container's interfaces if a pair is created, specifically in the case of type veth - // Note: This does not apply to loopback interfaces. - Mtu int `json:"mtu"` - - // TxQueueLen sets the tx_queuelen value for the interface and will be mirrored on both the host and - // container's interfaces if a pair is created, specifically in the case of type veth - // Note: This does not apply to loopback interfaces. - TxQueueLen int `json:"txqueuelen"` - - // HostInterfaceName is a unique name of a veth pair that resides on in the host interface of the - // container. - HostInterfaceName string `json:"host_interface_name"` - - // HairpinMode specifies if hairpin NAT should be enabled on the virtual interface - // bridge port in the case of type veth - // Note: This is unsupported on some systems. - // Note: This does not apply to loopback interfaces. - HairpinMode bool `json:"hairpin_mode"` -} - -// Routes can be specified to create entries in the route table as the container is started -// -// All of destination, source, and gateway should be either IPv4 or IPv6. -// One of the three options must be present, and omitted entries will use their -// IP family default for the route table. For IPv4 for example, setting the -// gateway to 1.2.3.4 and the interface to eth0 will set up a standard -// destination of 0.0.0.0(or *) when viewed in the route table. -type Route struct { - // Sets the destination and mask, should be a CIDR. Accepts IPv4 and IPv6 - Destination string `json:"destination"` - - // Sets the source and mask, should be a CIDR. Accepts IPv4 and IPv6 - Source string `json:"source"` - - // Sets the gateway. Accepts IPv4 and IPv6 - Gateway string `json:"gateway"` - - // The device to set this route up for, for example: eth0 - InterfaceName string `json:"interface_name"` -} |