diff options
Diffstat (limited to 'kube2msb/src/vendor/github.com/opencontainers/runc/libcontainer/configs/network.go')
| -rw-r--r-- | kube2msb/src/vendor/github.com/opencontainers/runc/libcontainer/configs/network.go | 72 |
1 files changed, 72 insertions, 0 deletions
diff --git a/kube2msb/src/vendor/github.com/opencontainers/runc/libcontainer/configs/network.go b/kube2msb/src/vendor/github.com/opencontainers/runc/libcontainer/configs/network.go new file mode 100644 index 0000000..ccdb228 --- /dev/null +++ b/kube2msb/src/vendor/github.com/opencontainers/runc/libcontainer/configs/network.go @@ -0,0 +1,72 @@ +package configs + +// Network defines configuration for a container's networking stack +// +// The network configuration can be omitted from a container causing the +// container to be setup with the host's networking stack +type Network struct { + // Type sets the networks type, commonly veth and loopback + Type string `json:"type"` + + // Name of the network interface + Name string `json:"name"` + + // The bridge to use. + Bridge string `json:"bridge"` + + // MacAddress contains the MAC address to set on the network interface + MacAddress string `json:"mac_address"` + + // Address contains the IPv4 and mask to set on the network interface + Address string `json:"address"` + + // Gateway sets the gateway address that is used as the default for the interface + Gateway string `json:"gateway"` + + // IPv6Address contains the IPv6 and mask to set on the network interface + IPv6Address string `json:"ipv6_address"` + + // IPv6Gateway sets the ipv6 gateway address that is used as the default for the interface + IPv6Gateway string `json:"ipv6_gateway"` + + // Mtu sets the mtu value for the interface and will be mirrored on both the host and + // container's interfaces if a pair is created, specifically in the case of type veth + // Note: This does not apply to loopback interfaces. + Mtu int `json:"mtu"` + + // TxQueueLen sets the tx_queuelen value for the interface and will be mirrored on both the host and + // container's interfaces if a pair is created, specifically in the case of type veth + // Note: This does not apply to loopback interfaces. + TxQueueLen int `json:"txqueuelen"` + + // HostInterfaceName is a unique name of a veth pair that resides on in the host interface of the + // container. + HostInterfaceName string `json:"host_interface_name"` + + // HairpinMode specifies if hairpin NAT should be enabled on the virtual interface + // bridge port in the case of type veth + // Note: This is unsupported on some systems. + // Note: This does not apply to loopback interfaces. + HairpinMode bool `json:"hairpin_mode"` +} + +// Routes can be specified to create entries in the route table as the container is started +// +// All of destination, source, and gateway should be either IPv4 or IPv6. +// One of the three options must be present, and omitted entries will use their +// IP family default for the route table. For IPv4 for example, setting the +// gateway to 1.2.3.4 and the interface to eth0 will set up a standard +// destination of 0.0.0.0(or *) when viewed in the route table. +type Route struct { + // Sets the destination and mask, should be a CIDR. Accepts IPv4 and IPv6 + Destination string `json:"destination"` + + // Sets the source and mask, should be a CIDR. Accepts IPv4 and IPv6 + Source string `json:"source"` + + // Sets the gateway. Accepts IPv4 and IPv6 + Gateway string `json:"gateway"` + + // The device to set this route up for, for example: eth0 + InterfaceName string `json:"interface_name"` +} |