clean MR codebase

Issue-ID: DMAAP-1199
Change-Id: Ieff7939b02a8987b6101dd1c0ec886b474f1fa82
Signed-off-by: sunil.unnava <sunil.unnava@att.com>

2 files changed, 0 insertions, 243 deletions

diff --git a/ajsc-shared-config/etc/aft.properties b/ajsc-shared-config/etc/aft.properties
deleted file mode 100644
index e46c976..0000000
--- a/ajsc-shared-config/etc/aft.properties
+++ /dev/null
@@ -1,37 +0,0 @@
-###############################################################################
-#  ============LICENSE_START=======================================================
-#  org.onap.dmaap
-#  ================================================================================
-#  Copyright © 2017 AT&T Intellectual Property. All rights reserved.
-#  ================================================================================
-#  Licensed under the Apache License, Version 2.0 (the "License");
-#  you may not use this file except in compliance with the License.
-#  You may obtain a copy of the License at
-#        http://www.apache.org/licenses/LICENSE-2.0
-#  
-#  Unless required by applicable law or agreed to in writing, software
-#  distributed under the License is distributed on an "AS IS" BASIS,
-#  WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-#  See the License for the specific language governing permissions and
-#  limitations under the License.
-#  ============LICENSE_END=========================================================
-#
-#  ECOMP is a trademark and service mark of AT&T Intellectual Property.
-#  
-###############################################################################
-# EEM: $Header: file:///opt/app/workload/d124csi1m1/cfengine_depot/mirror/1.0/cfengine/csi/cg03/release/1504/m2e/csi-shared-config/94.0.64/etc/aft.properties 118444 2015-05-19 07:59:38Z dh2924 $ID$
-# Flow test 319
-# The DEFAULT setup for this file is for deployment to soa cloud node which will use the "bundleconfig/etc/spm2.jks" location
-# For Testing Locally, you can set the system property, csiEnable=true, found within bundleconfig-local/etc/sysprops/sys-props.properties
-# and switch com.att.aft.keyStore and com.att.aft.trustStore values commented out below to "ajsc-shared-config/etc/spm2.jks"
-
-com.att.aft.discovery.client.environment=AFTUAT
-com.att.aft.discovery.client.latitude=35.318900
-com.att.aft.discovery.client.longitude=-80.762200
-com.att.aft.alias=fusionbus
-#com.att.aft.keyStore=ajsc-shared-config/etc/spm2.jks
-com.att.aft.keyStore=bundleconfig/etc/spm2.jks
-com.att.aft.keyStorePassword=<password>
-#com.att.aft.trustStore=ajsc-shared-config/etc/spm2.jks
-com.att.aft.trustStore=bundleconfig/etc/spm2.jks
-com.att.aft.trustStorePassword=<password>
diff --git a/ajsc-shared-config/etc/csm-config-app.properties b/ajsc-shared-config/etc/csm-config-app.properties
deleted file mode 100644
index 48ee7f6..0000000
--- a/ajsc-shared-config/etc/csm-config-app.properties
+++ /dev/null
@@ -1,206 +0,0 @@
-###############################################################################
-#  ============LICENSE_START=======================================================
-#  org.onap.dmaap
-#  ================================================================================
-#  Copyright © 2017 AT&T Intellectual Property. All rights reserved.
-#  ================================================================================
-#  Licensed under the Apache License, Version 2.0 (the "License");
-#  you may not use this file except in compliance with the License.
-#  You may obtain a copy of the License at
-#        http://www.apache.org/licenses/LICENSE-2.0
-#  
-#  Unless required by applicable law or agreed to in writing, software
-#  distributed under the License is distributed on an "AS IS" BASIS,
-#  WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-#  See the License for the specific language governing permissions and
-#  limitations under the License.
-#  ============LICENSE_END=========================================================
-#
-#  ECOMP is a trademark and service mark of AT&T Intellectual Property.
-#  
-###############################################################################
-Global.ExtendedProperty.AuthoritativeServers=${ChangeMe_csm.acfshost}:${ChangeMe_csm.acfsport}
-
-#Possible working server for troubleshooting csm related items (used when testing/using invokeService or invokeAdapter components)
-#Global.ExtendedProperty.AuthoritativeServers=q399csi1a1.vci.att.com:27550
-#
-# The settings in this file control the behavior of the CSM Framework. 
-# The majority of the settings in this file adhere to the following
-# pattern:
-# 
-#  [EntityType].[EntityId].[PropertyName]=[PropertyValue]
-# 
-# Where:
-# 
-#  [EntityType]    Identifies the type of entity (service or
-#                  service group) that's being configured.
-#  [EntityId]      Identifies the individual entity.
-#  [PropertyName]  Identifies the property that is being set.
-#  [PropertyValue] Is the actual property value.
-# 
-# In the formatting sample above, the EntityType can be setto one of the
-# following values:
-# 
-#  * 'Service' if an individual service is being configured.
-#  * 'Group 'if a service group is being configured.
-# 
-# The reference to 'entity' in the above description is intentionally
-# generic.  The CSM Framework supports the configuration of individual
-# services as well as groups of services.  The type of entity that is
-# actually being configured is determined by the value of the
-# [EntityType] portion of the property.
-# 
-# There are two values for [EntityId] that have a special meaning within
-# the CSM Framework:
-# 
-# 
-# DefaultService - Identifies the default configuration for any service
-#     that is not explicitly configured elsewhere in this file.
-# 
-# DefaultServiceGroup - This identifies the entity that provides the
-#     default configuration for any service group that is not explicitly
-#     configured elsewhere in this file.
-# 
-# DO NOT use either of these as the identifier for any of your
-# application-specific services or service groups.
-# 
-# The CSM Framework treats all entity identifiers in a case-insensitive
-# manner.  The entity ids 'Service1' and 'SERVICE1' are equivalant.  All
-# properties with the same [EntityId] will be applied to the same
-# configuration.  The CSM Framework framework also treats property names
-# in a case-insensitive manner.  'MaxRequestCount' and 'MAXREQUESTCOUNT'
-# are considered equivalent within the CSM framework.
-# 
-# The following properties are supported by the CSM Framework.  Any
-# properties that are entity-specific will include the '[EntityId].'
-# prefix.
-# 
-# [EntityType].[EntityId].Enabled - Indicates if the entity is enabled
-#     or disabled by default.  The value of this property must be either
-#     'true' or 'false'.
-# 
-# [EntityType].[EntityId].MaxRequestCount - The maximum number of
-#     requests that can be running at any point in time.  Once this limit is
-#     reached, the service is considered  to be 'flooded', and subsequent
-#     requests are refused until the request count drops to the level
-#     specified by the RestartThreshold property.  Once the restart
-#     threshold is reached, the service will be 'restarted' based on the
-#     values of the 'RestartFrequency' and 'RestartIncrement' properties.
-#     The value of this property must be a numeric value.
-#     The default value for this property is 20.
-# 
-# [EntityType].[EntityId].MaxStalledRequestCount - the maximum number of
-#     'stalled' requests that are allowed before subsequent requests are
-#     refused
-#     The value of this property must be a numeric value.
-#     The default value for this property is 10.
-# 
-# [EntityType].[EntityId].RestartThreshold - the process count level at
-#     which requests will be allowed to proceed whenever a service becomes
-#     'flooded'.  This property is only used if the total process count
-#     reaches the level set by the 'MaxRequestCount' property.  Once that
-#     occurs, subsequent requests will be refused until the active request
-#     count drops to the level specified by this property.  Once the active
-#     request count drops to the level specified by this property, the
-#     service will be 'restarted' based on the values of the
-#     'RestartFrequency' and 'RestartIncrement' properties.  To cause the
-#     CSM framework to allow subsequent requests to proceed as soon as the
-#     active request count drops below level level set by the
-#     'MaxRequestCount' property, just set this property to either -1 or 1
-#     less than the value of the 'MaxRequestCount' property.
-#     The value of this property must be a numeric value.
-#     The default value for this property is -1.
-# 
-# [EntityType].[EntityId].RestartIncrement - This property, along with
-#     the 'RestartFrequency' property helps determine how quickly the active
-#     request count will rise to the 'maximum request count' whenever a
-#     service is 'restarted' after becoming 'flooded'. The
-#     'RestartFrequency' property determines how frequenty the permissable
-#     number of active requests will be increased.  This property determines
-#     how much the permissible number of active requests will increase by
-#     whenever it is raised.  If this property is set to a positive value,
-#     then the 'RestartFrequency' property must also be set to a positive
-#     value.  If this property is set to 0, then the 'RestartFrequency'
-#     property must also be set to 0.  In other words, either both
-#     properties are 0 or both properties are greater than 0.  When both
-#     properties are set to 0, then the permissable number of active
-#     requests immediately rises back up to the maximum request count once
-#     it has droppedback down to the 'restart threshold'.  When both
-#     properties are greater than 0, then the permissable number of active
-#     requests gradually rises to the maximum request count.
-#     The value of this property must be a numeric value greater than or equal to 0.
-#     The default value for this property is 0.
-# 
-# [EntityType].[EntityId].RestartFrequency - This property, along with
-#     the 'RestartIncrement' property helps determine how quickly the active
-#     request count will rise to the 'maximum request count' whenever a
-#     service is 'restarted' after becoming 'flooded'. The
-#     'RestartIncrement' property determines how quickly the permissable
-#     number of active requests will be increased.  This property determines
-#     how frequently  that increase will occur.  If this property is set to
-#     a positive value, then the 'RestartIncrement' property must also be
-#     set to a positive value.  If this property is set to 0, then the
-#     'RestartIncrement' property must also be set to 0.  In other words,
-#     either both properties are 0 or both properties are greater than 0. 
-#     When both properties are set to 0, then the permissable number of
-#     active requests immediately rises back up to the maximum request count
-#     once it has droppedback down to the 'restart threshold'.  When both
-#     properties are greater than 0, then the permissable number of active
-#     requests gradually rises to the maximum request count.
-#     The value of this property must be a numeric value greater than or equal to 0.
-#     The default value for this property is 0.
-# 
-# [EntityType].[EntityId].ServiceGroupId - This property is only
-#     relevant for entities that are configured as services (i.e. the
-#     [EntityType] portion of the property is set to 'Service').  When the
-#     'ServiceGroupId' property is set to a non-blank value, the behavior of
-#     the service is controled by the configuration of the corresponding
-#     service group.  There is no default value for this property.
-# 
-# [EntityType].[EntityId].Timeout - the timeout, in milliseconds, for
-#     each process that is controlled by this configuration.  Once the
-#     duration of a process exceeds this value, the process will be
-#     considered to have entered a 'stalled' state.  The default value for
-#     this property is 10000.
-# 
-# FrameworkEnabled: - This is the one property that is not specific to a
-#     single entity.  This property determines whether the entire CSM
-#     Framework is enabled or disabled.  When disabled, the CSM Framework
-#     does not track any process counts.  All requests to access a service
-#     are allowed, regardless of the current level of activity.  The value
-#     of this property must be either 'true' or 'false'.
-# 
-
-#
-# Enables the CSM Framework so that it can manage interactions with external
-# services and/or resources.  To disable the CSM Framework, simply set
-# this property to false.
-#
-FrameworkEnabled=true
-
-#
-# These are the default settings for any service that is no explicitly configured
-# below.  A few things to note about this configuration:
-#  1) The "Enabled" property is not explicitly set.  Instead, we are relying
-#     on the default value of 'true'.
-#  2) The Timeout and Type properties are also not explicitly set.  Again, we
-#     are relying on the default values for these properties.
-#  
-Service.DefaultService.Enabled=true
-Service.DefaultService.MaxRequestCount=30
-Service.DefaultService.MaxStalledRequestCount=20
-Service.DefaultService.Timeout=30000
-Service.DefaultService.RestartThreshold=-1
-Service.DefaultService.AutoPurgeAfter=150000
-
-
-#
-# These are the default settings for any service group that is referenced in 
-# a service configuration but not configured below.
-# 
-# Currently CSI does not use any service group configurations!
-#
-#Group.DefaultGroup.MaxRequestCount=-1
-#Group.DefaultGroup.MaxStalledRequestCount=-1
-#Group.DefaultGroup.RestartThreshold=-1
-#Group.DefaultGroup.Timeout=-1