blob: d7ecee45e6c8b1a343dc8d3a1d7a2d8c20e6c921 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
|
#-------------------------------------------------------------------------------
# ============LICENSE_START====================================================
# * org.onap.aaf
# * ===========================================================================
# * Copyright © 2017 AT&T Intellectual Property. All rights reserved.
# * ===========================================================================
# * Licensed under the Apache License, Version 2.0 (the "License");
# * you may not use this file except in compliance with the License.
# * You may obtain a copy of the License at
# *
# * http://www.apache.org/licenses/LICENSE-2.0
# *
# * Unless required by applicable law or agreed to in writing, software
# * distributed under the License is distributed on an "AS IS" BASIS,
# * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# * See the License for the specific language governing permissions and
# * limitations under the License.
# * ============LICENSE_END====================================================
# *
# * ECOMP is a trademark and service mark of AT&T Intellectual Property.
# *
#-------------------------------------------------------------------------------
NOTE: You may find slight differences between this readme doc and your actual output in places such as <YOUR_ATTUID>, times, or other such fields that vary for each run.
Do NOT replace anything inside square brackets such as [user.name] Some commands listed here use this notation, but they are set up to work by just copying & pasting the entire command.
run command: sh ./tc MTC_Appr1
you should see: MTC_Appr1
SUCCESS! [MTC_Appr1.2014-11-03_11-26-26]
open a broswer and goto the gui for the machine you're on. For example, this is the home page on test machine zltv1492:
https://zltv1492.vci.att.com:8085/gui/home
click on My Approvals
click the submit button at the bottom of the form with no approve or deny buttons selected
you should see: No Approvals have been sent. Try again
click "Try again" link
you should see: The Approval Request page
NOTE: a radio button is a (filled or unfilled) circle under approve or deny
click the select all link for approve
you should see: all radio buttons under approve should be selected
click the select all link for deny
you should see: all radio buttons under deny should be selected
click the reset button at the bottom of the form
you should see: NO radio buttons should be selected
Try to select both approve and deny for a single entry
you should: not be able to
approve or deny entries as you like, then click submit
after you have submitted all approvals, go back to My Approvals page
you should see: No Approvals to process at this time
in your command line,
run command: aafcli ns list name com.test.appr.@[user.name].myProject
NOTE: what you see here will depend on which entries you approved and denied. Included are 2 examples of what you can see:
1) If you approve everything
List Namespaces by Name[com.test.appr.<YOUR_ATTUID>.myProject]
--------------------------------------------------------------------------------
com.test.appr.<YOUR_ATTUID>.myProject
Administrators
<YOUR_ATTUID>@csp.att.com
Responsible Parties
<YOUR_ATTUID>@csp.att.com
2) If you deny everything
List Namespaces by Name[com.test.appr.<YOUR_ATTUID>.myProject]
--------------------------------------------------------------------------------
run command: sh ./tc MTC_Appr2 dryrun
you should see: a lot of output. It's fine if you see errors for this command.
run command: aafcli ns list name com.test.appr
you should see: List Namespaces by Name[com.test.appr]
--------------------------------------------------------------------------------
run command: aafcli ns list name com.test.appr.@[user.name]
you should see: List Namespaces by Name[com.test.appr.<YOUR_ATTUID>]
--------------------------------------------------------------------------------
|