1 files changed, 0 insertions, 101 deletions
diff --git a/authz-test/TestSuite/Instructions_for_MTCs/MTC_Appr_README.txt b/authz-test/TestSuite/Instructions_for_MTCs/MTC_Appr_README.txt
deleted file mode 100644
index d7ecee45..00000000
--- a/authz-test/TestSuite/Instructions_for_MTCs/MTC_Appr_README.txt
+++ /dev/null
@@ -1,101 +0,0 @@
-#-------------------------------------------------------------------------------
-# ============LICENSE_START====================================================
-# * org.onap.aaf
-# * ===========================================================================
-# * Copyright © 2017 AT&T Intellectual Property. All rights reserved.
-# * ===========================================================================
-# * Licensed under the Apache License, Version 2.0 (the "License");
-# * you may not use this file except in compliance with the License.
-# * You may obtain a copy of the License at
-# * 
-#  *      http://www.apache.org/licenses/LICENSE-2.0
-# * 
-#  * Unless required by applicable law or agreed to in writing, software
-# * distributed under the License is distributed on an "AS IS" BASIS,
-# * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# * See the License for the specific language governing permissions and
-# * limitations under the License.
-# * ============LICENSE_END====================================================
-# *
-# * ECOMP is a trademark and service mark of AT&T Intellectual Property.
-# *
-#-------------------------------------------------------------------------------
-NOTE: You may find slight differences between this readme doc and your actual output in places such as <YOUR_ATTUID>, times, or other such fields that vary for each run.
-
-Do NOT replace anything inside square brackets such as [user.name] Some commands listed here use this notation, but they are set up to work by just copying & pasting the entire command.
-
-run command:		sh ./tc MTC_Appr1
-you should see:		MTC_Appr1
-					SUCCESS! [MTC_Appr1.2014-11-03_11-26-26]
-
-
-open a broswer and goto the gui for the machine you're on. For example, this is the home page on test machine zltv1492: 
-https://zltv1492.vci.att.com:8085/gui/home 
-
-click on My Approvals
-
-click the submit button at the bottom of the form with no approve or deny buttons selected
-
-you should see:     No Approvals have been sent. Try again
-
-click "Try again" link
-
-you should see:     The Approval Request page
-
-NOTE: a radio button is a (filled or unfilled) circle under approve or deny
-click the select all link for approve
-
-you should see:     all radio buttons under approve should be selected
-
-click the select all link for deny
-
-you should see:     all radio buttons under deny should be selected
-
-click the reset button at the bottom of the form
-
-you should see:     NO radio buttons should be selected
-
-Try to select both approve and deny for a single entry
-
-you should:         not be able to
-
-approve or deny entries as you like, then click submit
-
-after you have submitted all approvals, go back to My Approvals page
-
-you should see:     No Approvals to process at this time
-
-in your command line,
-run command:		aafcli ns list name com.test.appr.@[user.name].myProject
-
-NOTE: what you see here will depend on which entries you approved and denied. Included are 2 examples of what you can see:
-
-1) If you approve everything
-
-List Namespaces by Name[com.test.appr.<YOUR_ATTUID>.myProject]
---------------------------------------------------------------------------------
-com.test.appr.<YOUR_ATTUID>.myProject
-    Administrators
-        <YOUR_ATTUID>@csp.att.com                                                      
-    Responsible Parties
-        <YOUR_ATTUID>@csp.att.com                                                      
-
-
-2) If you deny everything
-
-List Namespaces by Name[com.test.appr.<YOUR_ATTUID>.myProject]
---------------------------------------------------------------------------------
-
-
-run command:		sh ./tc MTC_Appr2 dryrun
-you should see:     a lot of output. It's fine if you see errors for this command.
-
-run command:        aafcli ns list name com.test.appr
-you should see:     List Namespaces by Name[com.test.appr]
---------------------------------------------------------------------------------
-
-
-run command:        aafcli ns list name com.test.appr.@[user.name]
-you should see:     List Namespaces by Name[com.test.appr.<YOUR_ATTUID>]
---------------------------------------------------------------------------------
-